Abstract Ocean Rivian Emblem - Spacing?

[bulldogz400]

Good afternoon!

Recently purchased an R1S which has a Satin PPF wrap. They removed all badges when doing the wrap, and the previous owner decided to leave it de-badged (aside from the hood and c-pillar).

I have decided to re-badge the R1S (at least some of it), and have an issue. Since the old lettering and any remnants of the old lettering is no longer present, I don't know exactly where to place the lettering / emblems. Specifically, how high / away from the body lines should the letters go on the doors, for the rear R1S emblem, etc?

I reached out to Abstract Ocean and they are checking, but claimed they aren't sure either. They messaged me saying they don't have an R1S to check, and typically installation of their emblems happens at the same time as removal. @AO_Pete tagging you to make sure this is correct.

Can anybody give me some guidance by taking a few quick measurements? Picture for reference. Thanks!

Sponsored

 

[AO_Pete]

Yeah, I was chatting this over with Christal earlier. I looked around online, there's no guidelines I can find anywhere. I know I saw a thread somewhere where another owner provided the basic measurements, but I've not been able to find that. Hoping someone else can jump in with a couple of quick pics with a measure and rear & side emblems.

 

[bulldogz400]

Yeah, I was chatting this over with Christal earlier. I looked around online, there's no guidelines I can find anywhere. I know I saw a thread somewhere where another owner provided the basic measurements, but I've not been able to find that. Hoping someone else can jump in with a couple of quick pics with a measure and rear & side emblems.

Thanks!

If any good samaritan is able to take a few measurements it would be greatly appreciated!

 

[UnsungZero_OldTimeAdMan]

No guides available. And if my installer hadn't thrown out AO's foam guide, I would've offered them (at least for the doors).

 

[AO_Pete]

yeah. Based on the install video at around 8:30 in, the side emblems are about an inch off the panel fold, and 2" from the leading edge of the door. I think as long as they're in about the right spot, and the same spot on both side, it would look great. We don't have our R1T at the moment, otherwise I'd at least measure that (not the best guide though, we've gone through a lot of emblems with all the testing).

 

[bulldogz400]

yeah. Based on the install video at around 8:30 in, the side emblems are about an inch off the panel fold, and 2" from the leading edge of the door. I think as long as they're in about the right spot, and the same spot on both side, it would look great. We don't have our R1T at the moment, otherwise I'd at least measure that (not the best guide though, we've gone through a lot of emblems with all the testing).

Thanks! If anyone is willing to just take a couple quick measurements on their OEM lettering and emblem it would be greatly appreciated. Just want to make sure I get it correct, or as close as I can . Cheers

 

[MidnightRivian]

The V on the Back lines up with the button to open the trunk

https://www.rivianforums.com/forum/threads/rivian-side-emblem-measurement-help.29110/

 

[ReyvaRivian]

Little late to party hope this helps. Took some photos, adjust for some margin of error - used reference point (side emblem door front trim and bottom ridge, rear bottom ridge)

Also added with the Template that comes from AbstractOcean for better measurements.

Quick shoutout for AO team they were fantastic and definitely recommend for anyone considering mods for your Rivian.

 

[bigsky]

I had my R1S debadged and most emblems removed. I bought the lettering and badging from Rivian ( all but the compass emblems on hood and c-pillar, $450). They all came with templates for perfect installl.
I myself did take tons of measurements on the badging locations, can dig up info if interested.

 

[AO_Pete]

Little late to party hope this helps...

Late to the party maybe, but you came with the good stuff ?

 

[R1Sky Business]

Forum comes through again !!!!

 

[bulldogz400]

HUGE THANKS to Reyva and Midnight!

Drinks on me if you're ever in Las Vegas!

 

[Riv E In]

Little late to party hope this helps. Took some photos, adjust for some margin of error - used reference point (side emblem door front trim and bottom ridge, rear bottom ridge)

Also added with the Template that comes from AbstractOcean for better measurements.

Quick shoutout for AO team they were fantastic and definitely recommend for anyone considering mods for your Rivian.

Just came across this. Super helpful! Any chance someone could hook me up with the rear R1S location measurements?

Sponsored