Camp speaker drawer replacement by TWRAPS (preview)

[k9ltd3]

Looking forward to this being available.

On a separate note, I've held off on the floor console organizer, however, if I get this, would likely get both. My question, are you going to offer a modified version of it to slot out the front portion of it so the new storage tray can still slide in and out. With the non-used camp speaker, wasn't an issue, but now that that will be a usable storage drawer, wouldn't want to have pull out the organizer every time I need to access it, which would be quite often.

Possibly it's as simple as just trimming just the front end? Or your program maybe can be revised to lower the front edge a little? Appears it wouldn't need much (see image below from your site)

And, just throwing it out there again, still would love for rear half (toward front of truck) to tilt up and allow for a little deeper storage. With the cover on it, would be a great place to put your phone. I know you said that complicates 3D printing. That was a few months ago, so just checking to see if there's been any further thought given to that?

Certainly buying the drawer storage. Likely will buy the console organizer if the front edge can be trimmed to allow the drawer to come out with it in.

Thank you.

I'd say get a Dremel and trim the floor organizer so it can go in and out.

Sponsored

 

[twraps]

Happy to say that the camp speaker drawer should be available to buy next week some time. I finally have a way of making it!

 

[Elitewillie]

any chance for a lock?

Definitely love the idea of a lock. Could use it as a gun storage.

 

[Gman]

Happy to say that the camp speaker drawer should be available to buy next week some time. I finally have a way of making it!

Hey- can we order now?
Any pics of it?

 

[twraps]

Hey- can we order now?
Any pics of it?

Sorry not yet...waiting for more hardware to come. I finally have a verification of being able to make it (special new printer) but I only have one of these now and each print is about 9hrs...I ordered a bunch more today, they will come next week and then I can start selling it. Will make a few small adjustments in the meantime and make photos later this week to post.

 

[jebinc]

Sorry not yet...waiting for more hardware to come. I finally have a verification of being able to make it (special new printer) but I only have one of these now and each print is about 9hrs...I ordered a bunch more today, they will come next week and then I can start selling it. Will make a few small adjustments in the meantime and make photos later this week to post.

Hi Ilya - Any updates on this project?

 

[twraps]

Hi Ilya - Any updates on this project?

Yes, I expect to release it later today and shipping to start tomorrow. It’s already in production just finalizing the leather insert today and we are done

 

[JacobTheTechGuy]

Yes, I expect to release it later today and shipping to start tomorrow. It’s already in production just finalizing the leather insert today and we are done

Excited to see it!

 

[twraps]

Excited to see it!

Here is what it looks like... I will finish the leather pads today and will make the listing, and we can start shipping tomorrow Unfortunately it will be in generic Uline box for the next month or so, as our custom boxes for it will take a while to make.

 

[Gman]

When will you update web dite to allow for purchase?

 

[Gman]

Site

 

[COdogman]

Turned out great!

 

[jebinc]

Here is what it looks like... I will finish the leather pads today and will make the listing, and we can start shipping tomorrow Unfortunately it will be in generic Uline box for the next month or so, as our custom boxes for it will take a while to make.

Nice! Price?

 

[twraps]

Nice! Price?

Probably around $35, will have to do cost calculation a bit later today.

 

[sub]

Here is what it looks like... I will finish the leather pads today and will make the listing, and we can start shipping tomorrow Unfortunately it will be in generic Uline box for the next month or so, as our custom boxes for it will take a while to make.

Looks great. What material is the final design made out of? 3D printed ABS?

Sponsored