Search results

FYI. For gen 1, not sure about gen 2 vehicles. If you want to tap into the spare post/bolt on your battery, Littlefuse has bolt on fuses that are exactly like the factory fuses. Did not find this posted anywhere. It snaps into the factory clips perfectly and is used on a M8 bolt. They have other...

Guessing you rebooted your router? Changing the SSID name might help as posted previously. My Rivian charger had that issues when I got it. I changed it back to one SSID after that and it's been fine for two years for both the charger and R1. Also you say connect for the first time. You have...

I'm in I would be interested in adding stand alone buttons. I was thinking if someone could make something similar to Leviton quickport plates. You have a generic plate and offer different knobs, buttons, switches and blank filler plates. You match each button to what ever function you want to...

If this helps, since you have a Meridian and a T, not sure how much is the same. Mine is a 2023 R1S with the post Meridian system. I don't remember the voltage of the speakers. The colors look right but white/red would be the positive side. I would check it though. I only checked some of the...

Here is more info. I have not tried these yet so it may not work. These connectors look like Furukawa RS series and Sumitomo whatever series. I also found picture showing them used by Tesla/Nissan/Infinity. I might buy one of these kits and see if the contacts fit into the existing housing...

How long did you charge it? I have to charge mine for like an hour or two after it completely dies. Then it seems to behave normally.

If I was splicing that I would use either solder & flux & heat shrink, or a solder seal connector. The seal connector should have adhesive to keep moisture out. I prefer to add a very tiny dab of flux to the wires even with the seal type because the solder seems to flow better. You only need a...

That looks like the same panel connector as gen 1. Gen 1 has two compressors under the floor, behind the bumper. That seems like a lot of trouble and expense though. You can buy a 12 volt compressor. Assuming yours has a 12 volt socket next to the 110 volt outlet. I keep one in the vehicle...

Try this. https://www.rivianforums.com/forum/threads/interior-passenger-side-fuse-box.8397/page-2

Yes mine is showing that info. I'm using Android and the firmware for the charger is v03.04.12. Same model as yours. Seems like it took a while (weeks/month) for my firmware to update compared to others on the forum.

Here is how mine was set up.

We used to have that issue with both ice vehicles. I have used these for years and they have kept the rats out of the engine compartment for us. They are meant to wire up to 12 volts, and you would probably need two for the R1(front and back). Instead, I wired one to a transformer and mounted it...

Yes the pink wire that goes to the trailer should work.

Sorry, I don't know about any other setup. I have the stereo that came out after Meridian, from June 2023.

I may not understand the question. Mine is a box that gets an input digital signal from something else. The only thing "out" is speaker level. I really don't know about any other audio setup Rivian may be using.

I did check polarity on all connections. Yes it's possible my drawing is wrong. I would check it with a meter to be sure. White Violet is positive on my drawing for example, but it could be wrong. Maybe the factory sub is 180 out of phase?

I didn't. I only installed a mono amp for the subwoofer. I used the existing 35 amp 12 volt trailer(pink wire) that goes to the trailer plug. I made a Y adapter so both the sub and trailer have power. My small trailer should not use that circuit anyway. I fused it in the tub with a 30 amp fuse...

Yes, not too difficult. It is on the left side behind the felt. https://www.rivianforums.com/forum/threads/upgraded-the-sub-in-r1s-with-aftermarket-alpine-swr-t10-subwoofer.14310/...

Agree on a reset. Mine has done the same thing, and other proximity issues. A reset fixed it. Sometimes a issue came back until the next software update, but not the presenting at home problem.

I used the 35 amp trailer battery circuit so it switches off. I think I set the amp to detect a signal to power it up. I guess if you wire a new circuit to the battery, you could still use that trailer power just as a switched voltage.