DIY 3D-Printed Phone Mount Solution for the R1S, Thoughts?

[narmstrong79]

Clips securely into the dash gaps between the two screens without any tape or screws

I've printed it in a PETG filament to hopefully withstand summer heat.

I didn't design these, I downloaded the files and bought a 25w qi2.2 magsafe puck that fit, I had an EveryAmp OBD2 dongle to get higher power output than what I can get from the USB-C ports when using other center console magsafe units.

What do you guys think of the placement?

Sponsored

 

[loqueid]

I printed one like this in PETG and loved the height. I could use my phone as a dash cam.
However, the tiny neck eventually snapped from repetitive use. Eventually, I just went with the TWRAPs because I haven't printed in asa yet. Plus, I wanted it to be Qi2 charger and the TWRAPs isn't much more after you buy the charger plus OBD2 adapter separately.

 

[narmstrong79]

I printed one like this in PETG and loved the height. I could use my phone as a dash cam.
However, the tiny neck eventually snapped from repetitive use. Eventually, I just went with the TWRAPs because I haven't printed in asa yet. Plus, I wanted it to be Qi2 charger and the TWRAPs isn't much more after you buy the charger plus OBD2 adapter separately.

I've had the @twraps center console one for the last 2+ years. It's great. I was looking at ways to put my phone more in view and faster charging

 

[twraps]

I've had the @twraps center console one for the last 2+ years. It's great. I was looking at ways to put my phone more in view and faster charging

We redesigned ours about a year ago and also it’s now Qi2.2 / 25W

 

[narmstrong79]

We redesigned ours about a year ago and also it’s now Qi2.2 / 25W

So you're tell me I need to buy a new one Any way i can buy one of the skins you use on the dual charging pad to update the one I have?

 

[SwampNut]

I prefer left, after trying both. Currently using the Twraps dash mount with a ball extension and the EveryAmp MagSafe with active cooling. That's necessary here in summer.

 

[twraps]

So you're tell me I need to buy a new one Any way i can buy one of the skins you use on the dual charging pad to update the one I have?

Yes, but depends on which version of it you have...pls DM me with a photo so I can make sure it's the current version as we no longer make the skins for the older one.

 

[narmstrong79]

Yes, but depends on which version of it you have...pls DM me with a photo so I can make sure it's the current version as we no longer make the skins for the older one.

I'm sure I have the older one, I've had it for 2+ years

 

[loqueid]

I prefer left, after trying both. Currently using the Twraps dash mount with a ball extension and the EveryAmp MagSafe with active cooling. That's necessary here in summer.

What are you using above the center screen? I would love that for OnX. Bonus if it can hold other things like a radio or other mounts.

 

[dradam]

I printed this and I’ve been using it for years. The placement is terrific horizontally or vertically.2023 vin . In fact, if you look at printables.com, you’ll find a mashup where I included an eyeglass holder with it, as well as a toothpick and tweezer holder. I also thickened the neck so that it wouldn’t break as easily.

 

[SwampNut]

What are you using above the center screen?

That is a Comma 3X, and now it's been relpaced with a Comma 4. They give you mostly self driving.

 

[loqueid]

That is a Comma 3X, and now it's been relpaced with a Comma 4. They give you mostly self driving.

I meant this:

 

[SwampNut]

Ah, gotcha, it's a CarPlay screen from CarPodGo, and yes, it can do OnX and other apps. One of the many reasons the Rivian should have CarPlay.

And there, I've now started yet another CP discussion.

 

[loqueid]

Ah, gotcha, it's a CarPlay screen from CarPodGo, and yes, it can do OnX and other apps. One of the many reasons the Rivian should have CarPlay.

And there, I've now started yet another CP discussion.

Neat! The 3D print for the mount is included in the video description. Thanks!

Sponsored