TOWING: Hitch Receiver? What are you using? RIVIAN has the hitch receiver sunk an extra 2" deep because of that stupid bumper....

[Captblue]

I use a Gen-Y I have the following, I use extended shank

https://www.tractorsupply.com/tsc/p...drop-2k-tw-16k-hitch-gh-051-versa-ball-gh-214

https://www.tractorsupply.com/tsc/p...-shank-21k-tri-ball-mount-12-in-length-gh-064

Sponsored

 

[LR4toR1S]

With mine upside down, the center point of the weld is 3.5 inches from the bumper. So there there would be about 2.5" between the rear most point of the bumper and a 2 inch ball.

Mine is a 4-in drop. It is not actually reversible since the ball is welded to the frame. I don't know off the top of my head if they make a 6-inch rise version, but if they did and it used the same angles there would be even more clearance.

They do but it has a reinforcement fin.....which then hits the bumper (that is what I have)

 

[sub]

They do but it has a reinforcement fin.....which then hits the bumper (that is what I have)

Curt's aluminum 6" ball mount doesn't have a reinforcement fin.

https://www.curtmfg.com/part/45362

 

[LR4toR1S]

Curt's aluminum 6" ball mount doesn't have a reinforcement pin.

https://www.curtmfg.com/part/45362

That one looks promising. How does aluminum hold up? I'm going to have to go down that rabbit hole tonight lol.

 

[sub]

That one looks promising. How does aluminum hold up? I'm going to have to go down that rabbit hole tonight lol.

I would think aluminum would last longer than steel since it won't rust.

But if you are worried about aluminum, one of these might work out for you. They have the support fin, but with the extra length that might not be a problem.

https://www.curtmfg.com/part/45080
https://www.curtmfg.com/part/45280

 

[Matchbox]

Lot of fancy hitches here. I don't know what I am doing correctly, but I am using a 6" hitch I have used for at least 25 years on a 4Runner and Tacoma and now my R1T. Probably bought at WalMart. No problems, it all fits, I have pulled trailers and boats no issues.

What I have found is that the hitch pin location in the R1T is much closer to the end of the receiver than with the Toyotas. I would have to get on the ground to install the pin in Toyotas while I can do it standing up with the R1T.

Now if I only did not need to get on my back to remove the bumper plate to get at the hitch....

 

[csharp]

Now if I only did not need to get on my back to remove the bumper plate to get at the hitch....

You should check out the thumbscrew replacements from @RWerksman. I have them on both our Rivians and they are amazing. No longer have to crawl on my back. And you cant beat $7 for the pair.

https://opensourceev.com/products/hitch-cover-thumbscrew-v2-pair

 

[onthebrake]

I've got this one from Harbor Freight.

In addition, I use two of these to keep down any rattling.

Been working well when I'm towing my camper:

I've got this one from Harbor Freight.

In addition, I use two of these to keep down any rattling.

Been working well when I'm towing my camper:

Im sure it’s fine, but with my experience with Harbor Freight products, I personally wouldn’t trust their trailer hitch. That’s where I wouldn’t skimp and try and save a few dollars. Just my opinion.

 

[mkhuffman]

You should check out the thumbscrew replacements from @RWerksman. I have them on both our Rivians and they are amazing. No longer have to crawl on my back. And you cant beat $7 for the pair.

https://opensourceev.com/products/hitch-cover-thumbscrew-v2-pair

They were one of my first purchases. They make the process so much easier.

 

[VandalSibs]

Im sure it’s fine, but with my experience with Harbor Freight products, I personally wouldn’t trust their trailer hitch. That’s where I wouldn’t skimp and try and save a few dollars. Just my opinion.

I don't feel like I skimped on it, but you are allowed your opinion and experiences.

The hitch fit my needs, was available in town opposed to waiting for something to fit, and wasn't unreasonably expensive. It exceeds the weight rating of the trailer I tow by nearly 3k lbs - and I anticipate that I won't need that extra capability for a long time (any newer trailer I might tow is still not gonna exceed that rating).

 

[Matchbox]

You should check out the thumbscrew replacements from @RWerksman. I have them on both our Rivians and they are amazing. No longer have to crawl on my back. And you cant beat $7 for the pair.

https://opensourceev.com/products/hitch-cover-thumbscrew-v2-pair

Just ordered. Thanks!

 

[LR4toR1S]

I would think aluminum would last longer than steel since it won't rust.

But if you are worried about aluminum, one of these might work out for you. They have the support fin, but with the extra length that might not be a problem.

https://www.curtmfg.com/part/45080
https://www.curtmfg.com/part/45280

That is the one I already have if you look at the 2nd or 3rd picture, that stupid fin doesn't clear the bumper when angled upwards. Thanks though!

 

[sub]

That is the one I already have if you look at the 2nd or 3rd picture, that stupid fin doesn't clear the bumper when angled upwards. Thanks though!

Which length do you have? (Not height).

9" (standard), 12" or 14"?

I have a hard time imagining how the fin gets in the way when it is 5 in longer than standard.

 

[Marchin_MTB]

If possible, would you mind sharing a photo of that clamp in-place? I'm really curious to see how good the fit is... Thanks!

Ooof, I need to clean my ball! Finally remembered to take a photo. Sorry for the wait.

 

[FlyYellow]

I've been very happy with the Cerakote Black Weigh Safe 4" Drop Hitch (Aluminum)

Sponsored